20% OFF Sale Until Wednesday! 

MASTER • KELIK • RESKIT • QUINTA STUDIO • EDUARD • GUNZE • VALLEJO • HGW • DEAD DESIGN • FIRMA49 • KOVOZÁVODY PROSTĚJOV • AZ MODEL • RS MODELS

 Sale Ends Wednesday, November 11, 2026!

1:35 KV-1 / KV-2 - Engine Deck Screen Version 1 (3D-Printed)

1:35 KV-1 / KV-2 - Engine Deck Screen Version 1 (3D-Printed)

12.36 €
Add to Cart

1:35 KV-1 / KV-2 - Engine Deck Screen Version 1 (3D-Printed)

The resin grille over the engine compartment of the KV-1 and KV-2, version 1 in 1:35 scale replaces the blind relief on the rear deck of an injection-molded kit. An accessory for a model, not a kit.

Scale1:35
Manufacturer Lithokraft
Product EAN9991117371242

Responsibility details are not available.

12.36 €
10.21 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

KV-1 and KV-2 grille over the engine compartment, version 1, 1:35

A resin grille over the engine compartment for models of the Soviet KV-1 and KV-2 heavy tanks in 1:35 scale. On the real vehicle a screen covered the intake and exhaust openings of the engine, and on an injection-molded kit this is the area where simplification shows up first: plastic manages it only as a blind relief, whereas a resin print holds thin ribbing. The version 1 designation points to one of the variants of the grille.

The real subject

The KV heavy tanks were built from 1940 in Leningrad and, after the evacuation, in Chelyabinsk, and individual plants as well as production batches differed in detail. The KV-1 with its 76.2 mm gun and the KV-2 with its 152 mm howitzer shared the chassis and the twelve-cylinder V-2 diesel engine, and it was the cooling of that engine which called for the large grilled openings on the rear deck. The shape and the division of the grilles are among the most reliable recognition features of the production versions. The upper surface of the engine compartment is also clearly visible from above on a finished model.

Building and painting tips

Small resin prints break off easily, so cut them away with a scalpel only at the moment you glue them. Level the mark left by the support with a fine file under water; resin dust is not to be inhaled. Wash the surface with warm soapy water before painting so that no uncured print resin is left on it. Make the joint with cyanoacrylate glue (super glue) and key the part with primer.

Who the set is for

  • Modelers who build the KV-1 or KV-2 and are working on the look of the rear deck
  • Diorama builders whose model is seen from above
  • More experienced modelers with resin and primer behind them

This is an accessory for modifying a model, not a kit of the vehicle. The parts are supplied unpainted; the base kit, the glue and the paints are not included in the package, unless stated otherwise. Check the exact contents on the box.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

It is not. It is an accessory set of small hardware that mounts onto a model built from another kit. The vehicle itself, the glue and the paints are not in the package, unless stated otherwise.

It depends on the kit. If the rear deck is molded as a blind relief, the surface is usually leveled and the grille is glued over it. Dry fit the part before gluing and check the shape on the box, because the grille patterns differed on the KV tanks.

Cyanoacrylate glue (super glue), ideally in a gel or medium consistency so that there is time to align the part. Polystyrene cement will not dissolve resin, so the joint does not hold and the part falls off before long.

Yes. Uncured print resin residue is left on the surface of a print and it stops paint from keying. Warm water with a drop of dish soap, a soft brush and thorough drying are enough. Then apply primer and only then the top coat.

Last seen

LithokraftLTH3501001:35

1:35 KV-1 / KV-2 - Engine Deck Screen Version 1 (3D-Printed)

The resin grille over the engine compartment of the KV-1 and KV-2, version 1 in 1:35 scale replaces the blind relief on the rear deck of an injection-molded kit. An accessory for a model, not a kit.
In stock
12.36 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.